`timescale 1ns/1ps // ECE 287 - Challenge testbench. You should NOT need to change this file. // Paste this into the LEFT pane (testbench.sv) on EDA Playground. // // It plays the part of the DE board and of you watching it: // 1. holds KEY[2] (reset) down, then lets go // 2. sets SW[7:0] to a seed and presses KEY[1] briefly // 3. lets the design run for about 12 "seconds" // 4. reads HEX2..HEX0 back into a number and, every time it changes, prints // it and draws the three displays in ASCII art // 5. prints a summary of what it saw // // "One second" is shrunk to ONE_SECOND = 100 clocks so the run is quick. // On the board your design uses the default of 50,000,000. // // In EPWave (it opens empty): Get Signals -> scope tb -> CLOCK_50, KEY, HEX0; // scope tb.dut -> random_number, load_seed, counter_start, one_second, val; // scope tb.dut.u_counter -> count -> Append Selected. Between ticks // random_number should change every clock while val holds still. module tb; localparam ONE_SECOND = 100; localparam SECONDS = 12; localparam [7:0] SEED = 8'hA5; // 165 reg CLOCK_50 = 1'b0; reg [3:0] KEY = 4'b1111; // nothing pressed reg [9:0] SW = 10'd0; wire [6:0] HEX0, HEX1, HEX2; wire [9:0] LEDR; random_display #(.ONE_SECOND(ONE_SECOND)) dut( .CLOCK_50(CLOCK_50), .KEY(KEY), .SW(SW), .HEX0(HEX0), .HEX1(HEX1), .HEX2(HEX2), .LEDR(LEDR)); always #10 CLOCK_50 = ~CLOCK_50; // 50 MHz // turn a seven-segment pattern back into a digit; 15 means "not a digit" function [3:0] seg_to_digit(input [6:0] s); case (s) 7'b1000000: seg_to_digit = 4'd0; 7'b1111001: seg_to_digit = 4'd1; 7'b0100100: seg_to_digit = 4'd2; 7'b0110000: seg_to_digit = 4'd3; 7'b0011001: seg_to_digit = 4'd4; 7'b0010010: seg_to_digit = 4'd5; 7'b0000010: seg_to_digit = 4'd6; 7'b1111000: seg_to_digit = 4'd7; 7'b0000000: seg_to_digit = 4'd8; 7'b0010000: seg_to_digit = 4'd9; default: seg_to_digit = 4'd15; endcase endfunction // one row of a seven-segment digit as 3 characters of ASCII art. // The segments are active low: a 0 bit draws, a 1 bit is blank. // row 0: _ segment 0 // row 1: |_| segments 5, 6, 1 // row 2: |_| segments 4, 3, 2 function [23:0] seg_row(input [6:0] s, input [1:0] row); case (row) 2'd0: seg_row = {" ", (s[0] ? " " : "_"), " "}; 2'd1: seg_row = {(s[5] ? " " : "|"), (s[6] ? " " : "_"), (s[1] ? " " : "|")}; 2'd2: seg_row = {(s[4] ? " " : "|"), (s[3] ? " " : "_"), (s[2] ? " " : "|")}; default: seg_row = " "; endcase endfunction // draw HEX2 HEX1 HEX0 side by side, the way they sit on the board task show_hex; begin $display(" %s %s %s", seg_row(HEX2, 2'd0), seg_row(HEX1, 2'd0), seg_row(HEX0, 2'd0)); $display(" %s %s %s", seg_row(HEX2, 2'd1), seg_row(HEX1, 2'd1), seg_row(HEX0, 2'd1)); $display(" %s %s %s", seg_row(HEX2, 2'd2), seg_row(HEX1, 2'd2), seg_row(HEX0, 2'd2)); end endtask integer cyc; integer shown; integer last_shown; integer last_change; integer changes; integer printed; integer min_gap; integer max_gap; integer gap; integer bad_digits; reg [3:0] d2, d1, d0; initial begin $dumpfile("dump.vcd"); $dumpvars(0, tb); // 1. reset KEY[2] = 1'b0; repeat (5) @(posedge CLOCK_50); #1 KEY[2] = 1'b1; // 2. seed: set the switches, press KEY[1] for 3 clocks, let go repeat (3) @(posedge CLOCK_50); #1 SW[7:0] = SEED; repeat (2) @(posedge CLOCK_50); #1 KEY[1] = 1'b0; repeat (3) @(posedge CLOCK_50); #1 KEY[1] = 1'b1; $display("Reset done, seed %0d loaded with KEY[1]. ONE_SECOND = %0d clocks.", SEED, ONE_SECOND); $display("Watching HEX2..HEX0 for about %0d seconds:", SECONDS); $display(" clock | shown | clocks since last change"); // 3 + 4. run and watch the display last_shown = -1; last_change = 0; changes = 0; printed = 0; min_gap = 1000000000; max_gap = 0; bad_digits = 0; for (cyc = 1; cyc <= SECONDS * ONE_SECOND; cyc = cyc + 1) begin @(posedge CLOCK_50); #1; d2 = seg_to_digit(HEX2); d1 = seg_to_digit(HEX1); d0 = seg_to_digit(HEX0); if (d2 == 15 || d1 == 15 || d0 == 15) begin if (bad_digits == 0) begin $display(" %5d | HEX shows something that is not a digit: HEX2=%b HEX1=%b HEX0=%b", cyc, HEX2, HEX1, HEX0); show_hex; end bad_digits = bad_digits + 1; end else begin shown = d2 * 100 + d1 * 10 + d0; if (shown != last_shown) begin if (last_shown == -1) begin if (printed < 40) begin $display(" %5d | %3d | (first value)", cyc, shown); show_hex; end end else begin gap = cyc - last_change; changes = changes + 1; if (gap < min_gap) min_gap = gap; if (gap > max_gap) max_gap = gap; if (printed < 40) begin $display(" %5d | %3d | %0d", cyc, shown, gap); show_hex; end end printed = printed + 1; if (printed == 40) $display(" ... (only the first 40 changes are printed)"); last_shown = shown; last_change = cyc; end end end // 5. summary $display(""); $display("===== SUMMARY ====="); if (bad_digits > 0) $display("* On %0d clocks the HEX outputs were not a 0-9 digit. Check your seven_segment wiring.", bad_digits); if (changes == 0) begin if (last_shown == -1) $display("* The display never showed a number."); else $display("* The display never changed. It stayed at %0d the whole time.", last_shown); end else begin $display("* The display changed %0d times in about %0d seconds.", changes, SECONDS); $display("* Clocks between changes: shortest %0d, longest %0d (one second here = %0d).", min_gap, max_gap, ONE_SECOND); if (min_gap < ONE_SECOND / 2) $display("* It is changing much faster than once a second."); else if (changes < SECONDS / 2) $display("* It is changing much slower than once a second."); else $display("* That looks like about one new number per second. Now check that the numbers look random, then try it on the board!"); end $finish; end endmodule